Mamiya Econotig Manual do Utilizador

EconotigRDescriptionArc Welding Power SourceProcessesGas Tungsten Arc(TIG) WeldingShielded Metal Arc(Stick) WeldingOM-303 155 795TMay 2005Visit our we

OM-303 Page 6Le rayonnement de l’arc génère des rayons visibles etinvisibles intenses (ultraviolets et infrarouges) suscep-tibles de causer des brûlur

OM-303 Page 72-3. Autres symboles relatifs à l’installation, au fonctionnement et à l’entretien del’appareil.Risque D’INCENDIE OU D’EXPLO-SIOND Ne pas

OM-303 Page 82-4. Principales normes de sécuritéSafety in Welding, Cutting, and Allied Processes, norme ANSI Z49.1,de l’American Welding Society, 550

OM-303 Page 9SECTION 3 − DEFINITIONS3-1. General Precautionary Label

OM-303 Page 103-2. Symbols And DefinitionsTig WeldingRemote Foot/HandControlStick Welding High TemperatureOutput Alternating Current Direct Current On

OM-303 Page 114-2. SpecificationsA. 60 Hertz ModelsRated Output at 20% DutyCycleWelding Amperage RangeAC High AC Low DCMax.OCVRated Output KVA

OM-303 Page 12SECTION 5 − INSTALLATION5-1. Selecting a LocationST-158 075Position unit so air can circulate.For information about sources ofhigh-frequ

OM-303 Page 135-3. Typical TIG Connections Ref. ST-157 858-AY Turn Off power before mak-ing connections.1 Remote Control2 TorchConnect to receptacles

OM-303 Page 145-4. Electrical Service GuideS-0092J. For 230 V models with wall receptacle, 100% duty cycle used to calculate data below. 20% duty cycl

OM-303 Page 15SECTION 6 − OPERATION6-1. ControlsRef. ST-155 790-F1 Weld Process SwitchUse switch to select weld process.In Stick position (down), weld

Miller Electric manufactures a full lineof welders and welding related equipment.For information on other quality Millerproducts, contact your local M

OM-303 Page 166-2. Example of Front Panel Amperage ControlIn Example:Range = DCPercentage of Range = 50%Weld Amperage = 33 A DCSelect percentage.Selec

OM-303 Page 176-4. Process and Material Thickness Guide LabelGuideline For Welding Process And Output For MaterialMaterial ThicknessMaterial And22 ga

OM-303 Page 18SECTION 7 − MAINTENANCE AND TROUBLESHOOTING7-1. Routine MaintenanceY Disconnect power before maintaining.. Maintain more often during s

OM-303 Page 19SECTION 8 − ELECTRICAL DIAGRAMSSB-154 141-CFigure 8-1. Circuit Diagram

OM-303 Page 20SECTION 9 − HIGH FREQUENCY9-1. Welding Processes Requiring High Frequencyhigh_freq1 11/96 − S-06931 High-Frequency VoltageHelps arc jump

OM-303 Page 219-3. Correct Installation1 High-Frequency Source (welding powersource with built-in HF or separate HFunit)Ground metal machine case, wor

OM−303 Page 22SECTION 10 − PARTS LISTST-801 399-D. Hardware is common andnot available unless listed.134 567891011121314151617181920212223242526272829

OM-303 Page 23DescriptionPartNo.Dia.Mkgs.ItemNo.Figure 10-1. Main AssemblyQuantity1 154 335 BEZEL, front 1. . . . . . . . . . . . . . . . . . . . .

OM−303 Page 24DescriptionPartNo.Dia.Mkgs.ItemNo.Figure Figure 10-1. Main Assembly (Continued)Quantity42 PL1 157 958 LIGHT, ind wht lens 28V 1. . . .

Notes

TABLE OF CONTENTSSECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbo

Notes

Warranty Questions?Call1-800-4-A-MILLERfor your localMiller distributor.miller_warr 1/05Your distributor also givesyou ...ServiceYou always get the fa

PRINTED IN USA © 2005 Miller Electric Mfg. Co. 1/05Miller Electric Mfg. Co.An Illinois Tool Works Company1635 West Spencer StreetAppleton, WI 54914 US

Notes

OM-303 Page 1SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USINGsom _3/05Y Warning: Protect yourself and others from injury — read and follow these pre

OM-303 Page 2Arc rays from the welding process produce intensevisible and invisible (ultraviolet and infrared) raysthat can burn eyes and skin. Sparks

OM-303 Page 31-3. Additional Symbols For Installation, Operation, And MaintenanceFIRE OR EXPLOSION hazard.D Do not install or place unit on, over, or

OM-303 Page 41-5. Principal Safety StandardsSafety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,from Global Engineering Documents (p

OM-303 Page 5SECTION 2 − CONSIGNES DE SÉCURITÉ − À LIRE AVANTUTILISATIONsom_fre 8/032-1. Signification des symbolesSignifie « Mise en garde. Faire pre